About to run Euro 0w40 on Buick 455

[loneryder]

M1 15w50 has 1320 Zinc

How much more would you want?

 

[Nicasio]

With all those cubes, that's probably a nice street cam. How's the vacuum?

Honestly these brakes could feel much better. I feel the need to look into one of them LEED rotary vane vacuum pump systems.

 

[Nicasio]

whats the spring peessures?

C&P from TA Performance website.

​	Product ID: TA_1435 400-430-455 Stage 1 Valve Springs .500 Lift
Factory Stage 1 replacement spring for mild to moderate cam combinations on any Big Block Buick O.D. 1.370 I.D. 0.850 90 lbs @ 1.900 315 lbs @ 1.400 Coil Bind 1.175

 

[Nicasio]

How much more would you want?

Just a bit more than the 0w40’s 1000 ppm

 

[BMW850]

Ok I’m about to do the yearly oil change on my Buick. It has a 455 with a mild hydraulic flat tappet cam. I know from previous posts and reading threads that it should be fine with running just the M1 Euro 0w40. My question is, can I mix some maybe M1 Delvac1 5w40 or V-Twin 20w50 to give it a little zinc boost? Would make me feel better knowing it would be View attachment 212903View attachment 212904above the normal 1k zinc number. What do y’all think of this Walmart concoction?

In recent years there have been entirely too many wiped cam lobes and ruined lifter failures in traditional American flat tappet engines, even though a variety of well respected brand name parts were typically used. These failures involved people using various high zinc oils, various high zinc Break-In oils, various Diesel oils, and various oils with aftermarket zinc additives added to the oil. They believed that any high zinc oil concoction is all they needed for wear protection during flat tappet engine break-in and after break-in. But, all of those failures have proven over and over again, that their belief in high zinc was nothing more than a MYTH, just as my test data has shown.

.
A high level of zinc/phos is simply no guarantee of providing sufficient wear protection. And to make matters even worse, excessively high levels of zinc/phos can actually “cause” DAMAGE your engine, rather than “prevent” it. Motor Oil Industry testing has found that motor oils with more than 1,400 ppm ZDDP, INCREASED long-term wear. And it was also found that motor oils with more than 2,000 ppm ZDDP started attacking the grain boundaries in the iron, resulting in camshaft spalling (pitting and flaking). The ZDDP value is simply the average of the zinc and the phosphorus values, then rounded down to the nearest 100 ppm (parts per million). from 540Rat

 

[SR5]

M1 15w50 has 1320 Zinc

That’s a good oil for heavy duty & high performance applications.

 

[burbguy82]

M1 15w50 has 1320 Zinc

Could you give some reference?

 

[Bullwinkle007]

Well I guess the six quarts of VR1 10w30 I dumped in it last were conventional. Funny I thought I had synthetic in it this whole time Definitely going synthetic on it now!
Does anyone know how much Zinc is in the Delvac1 5w40? I couldn’t find it on M1’s website. Here are the other’s Zinc numbers. I’m thinking 0w40 and one or two quarts of the V-Twin 20w50 Good Walmart concoction??

M1 ESP x3 0w40 = 990
M1 Supercar 0w40 = 990
M1 Euro 0w40 = 1000
M1 Supercar 5w50 = 1200
M1 TDT 5w40 = 1300
M1 15w50 = 1320
M1 V-Twin = 1770

What’s wrong with just going with Clsssic VR-1 20w-50? You hardly drive the nice ride.