New Amsoil OE 15W-40

Status
Not open for further replies.
"Original Equipment", in the same vein as 'OEM'.

They want you to follow the vehicle manufacturer's recommended OCI when using this oil, in both gas and diesel applications, whether it be an OLM, or a set interval.
 
Well - let's go ahead and start the rumor mill now ...
I'm sure people are already thinking it; I'm just the first to post it up.

Why is it so much cheaper? Some thoughts here:
1) it's not group IV, but perhaps III?
2) reduced add-pack to make the minimum OEM OCI, and not more
3) some combination of #1 and #2

Other lube makers are now making both PAO and also "other synthetic" options (Castrol, Mobil, etc come to mind). Why not Amsoil? I don't blame them at all; it's good marketing to open oneself up to another niche. Perahps they are in a position where it's time to admit that the "other" synthetics are valid, and proven, (even if they don't want to openly admit that in public with some full-blown statement).

I would contend that if one if going to OCI at the OEM intervals, there is little or no need for this product at all. But there are some syn junkies that just have to have syn, even Amsoil. This allows them the braggin' rights with less cost. I'll concede this: one market I could see at last some validity to is perhaps areas with ultra-cold temps, where the normal OCI is still going to be followed.

The product is NOT API licensed, despite their typical rhetoric. Here is the Amsoil approved/licensed list per the API as of 5-18-11 @ 0530 hours EST: http://eolcs.api.org/brandSearchResults.aspx?mode=&q=&p=68
The Amsoil OE product is only licensed in the PC grades, not HDEO.
 
Last edited:
Would this particular oil be a good choice over something like Mobil Delvac or the conventional Rotella?
 
Most likely they will move the para-synthetic out of the line up and have the same as the new oil line....

Three lines of diesel oils! grab up that 30wt diesel oil while you can. It might be gone.
 
Originally Posted By: jmimac351
Would this particular oil be a good choice over something like Mobil Delvac or the conventional Rotella?
What would make the oil any better? ?
 
Originally Posted By: LargeCarManX2
Most likely they will move the para-synthetic out of the line up and have the same as the new oil line....

Three lines of diesel oils! grab up that 30wt diesel oil while you can. It might be gone.


I don't think it will replace PCO 15w40.

PCO is still an 'old school' high-TBN, CI-4 oil. The new OE 15w40 is a new CJ-4 oil.

So the PCO is the low-cost CI-4 oil; while the OE 15w40 is the low-cost CJ-4 oil.
 
Question:
Why did AMSOIL develop AMSOIL OE 15w40 Synthetic Diesel Oil?
Answer:
Many vehicle owners are interested in the significant benefits of AMSOIL synthetic lubricant technology but want to maintain their vehicles by changing their oil at manufacturer recommendations. AMSOIL recognized a need for these vehicle and equipment owners to have a full synthetic AMSOIL product meeting their unique performance and pricing requirements.
In addition, due to persistent fuel dilution issues in 2007 and newer light duty turbo diesels and certain Caterpillar heavy duty engines, AMSOIL Premium 5W-40 Synthetic Diesel Oil (DEO) and Premium 15w40 Synthetic Diesel Oil (DME) cannot be used for extended oil drain intervals for these popular vehicles. AMSOIL OE 15w40 Synthetic Diesel Oil (OED) is a cost effective alternative for these owners/operators who desire the benefits of AMSOIL synthetic oil but are not able to extend oil drain intervals because of persistent engine oil fuel dilution issues.


Diesel fleets and installers have been asking for an oil like this.
 
Originally Posted By: Steve S
Originally Posted By: jmimac351
Would this particular oil be a good choice over something like Mobil Delvac or the conventional Rotella?
What would make the oil any better? ?


I have no idea, Steve. That's why I asked the question.
 
For a lack of better terms, this oil is a "decontented" version so that people who want to use Amsoil brand (either for bragging rights or some other emotional response) can still do so, and not have to spend as much money.

Of course, for normal OCIs, you can very likely get away with any "normal" oil and save even more money, but then there would be no Amsoil aura to enjoy ...


Very interested in seeing a VOA on this to see just what's "missing" from the other forumlations.
 
Last edited:
Originally Posted By: dnewton3

For a lack of better terms, this oil is a "decontented" version so that people who want to use Amsoil brand (either for bragging rights or some other emotional response) can still do so, and not have to spend as much money.

Of course, for normal OCIs, you can very likely get away with any "normal" oil and save even more money, but then there would be no Amsoil aura to enjoy ...


Very interested in seeing a VOA on this to see just what's "missing" from the other forumlations.


"decontented"

Wow.........are we at it again?

Glad you completely reworded your answer, some would have thought you have something against Amsoil. Your word choice of "missing" is interesting - just remember this is a CJ-4 oil so compare fairly. I doubt you will spot any thing "missing" in a $25 used oil analysis. But still we await your valuable input.

I think addyguy and mikedup1 (quoted from Amsoil as you noted) provided good early answers. Thanks.
 
Originally Posted By: dnewton3
Well - let's go ahead and start the rumor mill now ...
I'm sure people are already thinking it; I'm just the first to post it up.

Why is it so much cheaper? Some thoughts here:
1) it's not group IV, but perhaps III?
2) reduced add-pack to make the minimum OEM OCI, and not more
3) some combination of #1 and #2

Other lube makers are now making both PAO and also "other synthetic" options (Castrol, Mobil, etc come to mind). Why not Amsoil? I don't blame them at all; it's good marketing to open oneself up to another niche. Perahps they are in a position where it's time to admit that the "other" synthetics are valid, and proven, (even if they don't want to openly admit that in public with some full-blown statement).

I would contend that if one if going to OCI at the OEM intervals, there is little or no need for this product at all. But there are some syn junkies that just have to have syn, even Amsoil. This allows them the braggin' rights with less cost. I'll concede this: one market I could see at last some validity to is perhaps areas with ultra-cold temps, where the normal OCI is still going to be followed.

The product is NOT API licensed, despite their typical rhetoric. Here is the Amsoil approved/licensed list per the API as of 5-18-11 @ 0530 hours EST: http://eolcs.api.org/brandSearchResults.aspx?mode=&q=&p=68
The Amsoil OE product is only licensed in the PC grades, not HDEO.


Agreed, smart marketing and trying to capture more market share. Seems the oil wars are heating up. I see two things coming from this, consumer confusion, and possibly better prices for the educated customers. JMO
 
Originally Posted By: Pablo
Originally Posted By: dnewton3

For a lack of better terms, this oil is a "decontented" version so that people who want to use Amsoil brand (either for bragging rights or some other emotional response) can still do so, and not have to spend as much money.

Of course, for normal OCIs, you can very likely get away with any "normal" oil and save even more money, but then there would be no Amsoil aura to enjoy ...


Very interested in seeing a VOA on this to see just what's "missing" from the other forumlations.


"decontented"

Wow.........are we at it again?

Glad you completely reworded your answer, some would have thought you have something against Amsoil. Your word choice of "missing" is interesting - just remember this is a CJ-4 oil so compare fairly. I doubt you will spot any thing "missing" in a $25 used oil analysis. But still we await your valuable input.

I think addyguy and mikedup1 (quoted from Amsoil as you noted) provided good early answers. Thanks.



It is marketed as a CJ-4 lube, but I already linked the official API site page that shows it's not a licensed lube. You can call it what you want, but I don't buy into the whole "misrepresenation" of calling something API approved when it's clearly not. It is a marketing strategy; nothing more or less. I fully understand that the lack of API certification and license do not make a lube inferior, but it's disingenuous to infer this is a CJ-4 lube, when it's clearly not licensed in HDEO form, and I linked that proof earlier. Unless it's been updated at the API site in the last day or so, it's more of Amsoil's marketing games. This is a product that is marketed to CJ-4 environments, but it is NOT CJ-4 approved via the entity that issues that CJ-4 license, and nothing you or Amsoil can say alters that truth. I accept it, and agree, that the lack of API certification does not make this a bad oil; it is likely a very good oil. What this comes down to is the fact that Amsoil calls this a CJ-4 lube, but the issuing entity does not. Amsoil takes "poetic license" in the use of the API term. Nothing new here. And, to be fair, they are certainly not the only one to use this marketing approach. But, to be sure, this is NOT a "API CJ-4 licensed" lube. I would say this is a non-licensed product aimed at a licensed market; that is 100% accurate, nothing more or less.

As for the "decontented" comment, I stand by it. It's a generic description. I have not seen the VOAs yet, but I am comfortable in the presumtion that the product is not the same (either in base stocks or add-pack, or both) than some of their other more "premium" offerings such as DEO, etc. If nothing else, the reduction of OCI duration is a "decontented" conceptual characteristic contrasted to the other products, is it not? What would be your basis that you presume it's NOT "decontented"? If this product is not "decontented", then what would be the logic to sell a product that would be (essentially) the same as their other products, but at a lesser cost? Would that not erode the sales of the other products such as DEO, etc?

Or, perhaps just the opposite it true? Mabye this product is 100% the same as all the other HDEOs they have, but they are going after sales from a different angle. Perhaps they want people to buy MORE Amsoil by making the OCIs no greater than other "normal" oils, and that drives up their proffit margin by getting higher volume sales via greater frequency of purchases; in essence, the volume increase overcomes the lower price point? I don't know what the answer is; I didn't sit in the marketing meetings; I wasn't invited.

I applaud Amsoil for now exploring a market niche they previously ignored; that's good business. I HIGHLY suspect this new product is decontented in one or more areas. But I certainly agree that does not make it unworthy of the intended application.

I think it's fair to contend that all Amsoil's products will be capable of fully protecting against wear for the intended OCI. IOW - for the stated OCI limit, any Amsoil product will provide at least a minimum wear protection that would assure a very safe and healthy long life of the equipment. Amsoil has too good of a product reputation to risk putting out a product that would result in poor wear performance.

Here's what I know for sure by viewing the Amsoil site:
* the OE HDEO price is about 33% less than the other HDEO products they offer
* the OCI is 66% lower (a 1x factor vs. a 3x factor)

So, conceptually, I lose 66% capability (defined as the loss of OCI, but with no risk in wear protection) but only save about 33% money? I lose 2/3 of the OCI, but only save roughly 1/3 the money, for the same wear protection. For the sake of your side of the debate, let's say there is zero difference in base stock and add-pack. Even the OCI reduction is a "decontented" characteristic. I save 33% money, but loose 66% of capability in OCI? That, in my mind, is a "reduction of content". Why? Because when I pay for any product, I consider the actual performance of the product as part of the "content". The resulting "effects" of the use of a product are most certainly what I am paying for. In fact, that is my typical contention with the whole "dino vs syn" debate anyway. Syns are great products, but only if you use them in a manner that exceeds the break-even point vs some other option. And performance (wear reduction, cold cranking, life span, etc) are a BIG part of that "content" that I pay for. In fact, I am MUCH more concerned about RESULTS than I am VOAs. I'm sure this OE oil from Amsoil results in good wear protection at normal OCIs. Contrasted to the other lubes from Amsoil, if I pay a little less money for a lot less OCI, that is a loss of content, and if you cannot see that, then you and I simply don't agree on how to measure the value of life's offerings. This OE oil prouduct in HDEO form offers 2/3 less OCI for only 1/3 less money. Is that not a loss of content?

And I admit I have no proof, but I VERY MUCH SUSPECT that Amsoil ALSO reduced the factors that put cost into the oil, such as lesser cost base stocks, additives, etc. It would be foolish of Amsoil to NOT reduce their cost factors in this product, would it not? So the reality is that we KNOW there is a loss of content in regard to OCI versus cost, and at least some of us suspect there is also a physical elemental input reduction as well.

This is a good market strategy for Amsoil. They make more money via higher sales frequency for a product that will very likely provide no more wear protection than a competing oil over normal operations in OEM OCIs, and quite possibly costs them less money to make due to the likely reduction of physical inputs.
 
Last edited:
I went ahead and signed up for the preferred customer program the other day to get a decent discount on some gear oil I needed. When I picked it up I asked about the OE diesel oil and was told the additive package was different / not the same as the higher end stuff. It was suggested that there are some people who just do not buy into the longer drain intervals spec'd for their other oils and this OE oil, because of the price point, makes it more workable for that particular customer.

What I'll have to decide on is, is it better to spend $20/gal on this stuff or $10-$12/gal on Delvac, Rotella, etc. At almost twice the price, and shorter drain interval than the other synthetic, I'm not so sure. Rotella T6 is cheaper. I know very little about oil other than I prefer to have clean oil...
 
Last edited:
Originally Posted By: dnewton3
Originally Posted By: Pablo
Originally Posted By: dnewton3

For a lack of better terms, this oil is a "decontented" version so that people who want to use Amsoil brand (either for bragging rights or some other emotional response) can still do so, and not have to spend as much money.

Of course, for normal OCIs, you can very likely get away with any "normal" oil and save even more money, but then there would be no Amsoil aura to enjoy ...


Very interested in seeing a VOA on this to see just what's "missing" from the other forumlations.


"decontented"

Wow.........are we at it again?

Glad you completely reworded your answer, some would have thought you have something against Amsoil. Your word choice of "missing" is interesting - just remember this is a CJ-4 oil so compare fairly. I doubt you will spot any thing "missing" in a $25 used oil analysis. But still we await your valuable input.

I think addyguy and mikedup1 (quoted from Amsoil as you noted) provided good early answers. Thanks.



It is marketed as a CJ-4 lube, but I already linked the official API site page that shows it's not a licensed lube. You can call it what you want, but I don't buy into the whole "misrepresenation" of calling something API approved when it's clearly not. It is a marketing strategy; nothing more or less. I fully understand that the lack of API certification and license do not make a lube inferior, but it's disingenuous to infer this is a CJ-4 lube, when it's clearly not licensed in HDEO form, and I linked that proof earlier. Unless it's been updated at the API site in the last day or so, it's more of Amsoil's marketing games. This is a product that is marketed to CJ-4 environments, but it is NOT CJ-4 approved via the entity that issues that CJ-4 license, and nothing you or Amsoil can say alters that truth. I accept it, and agree, that the lack of API certification does not make this a bad oil; it is likely a very good oil. What this comes down to is the fact that Amsoil calls this a CJ-4 lube, but the issuing entity does not. Amsoil takes "poetic license" in the use of the API term. Nothing new here. And, to be fair, they are certainly not the only one to use this marketing approach. But, to be sure, this is NOT a "API CJ-4 licensed" lube. I would say this is a non-licensed product aimed at a licensed market; that is 100% accurate, nothing more or less.

As for the "decontented" comment, I stand by it. It's a generic description. I have not seen the VOAs yet, but I am comfortable in the presumtion that the product is not the same (either in base stocks or add-pack, or both) than some of their other more "premium" offerings such as DEO, etc. If nothing else, the reduction of OCI duration is a "decontented" conceptual characteristic contrasted to the other products, is it not? What would be your basis that you presume it's NOT "decontented"? If this product is not "decontented", then what would be the logic to sell a product that would be (essentially) the same as their other products, but at a lesser cost? Would that not erode the sales of the other products such as DEO, etc?

Or, perhaps just the opposite it true? Mabye this product is 100% the same as all the other HDEOs they have, but they are going after sales from a different angle. Perhaps they want people to buy MORE Amsoil by making the OCIs no greater than other "normal" oils, and that drives up their proffit margin by getting higher volume sales via greater frequency of purchases; in essence, the volume increase overcomes the lower price point? I don't know what the answer is; I didn't sit in the marketing meetings; I wasn't invited.

I applaud Amsoil for now exploring a market niche they previously ignored; that's good business. I HIGHLY suspect this new product is decontented in one or more areas. But I certainly agree that does not make it unworthy of the intended application.

I think it's fair to contend that all Amsoil's products will be capable of fully protecting against wear for the intended OCI. IOW - for the stated OCI limit, any Amsoil product will provide at least a minimum wear protection that would assure a very safe and healthy long life of the equipment. Amsoil has too good of a product reputation to risk putting out a product that would result in poor wear performance.

Here's what I know for sure by viewing the Amsoil site:
* the OE HDEO price is about 33% less than the other HDEO products they offer
* the OCI is 66% lower (a 1x factor vs. a 3x factor)

So, conceptually, I lose 66% capability (defined as the loss of OCI, but with no risk in wear protection) but only save about 33% money? I lose 2/3 of the OCI, but only save roughly 1/3 the money, for the same wear protection. For the sake of your side of the debate, let's say there is zero difference in base stock and add-pack. Even the OCI reduction is a "decontented" characteristic. I save 33% money, but loose 66% of capability in OCI? That, in my mind, is a "reduction of content". Why? Because when I pay for any product, I consider the actual performance of the product as part of the "content". The resulting "effects" of the use of a product are most certainly what I am paying for. In fact, that is my typical contention with the whole "dino vs syn" debate anyway. Syns are great products, but only if you use them in a manner that exceeds the break-even point vs some other option. And performance (wear reduction, cold cranking, life span, etc) are a BIG part of that "content" that I pay for. In fact, I am MUCH more concerned about RESULTS than I am VOAs. I'm sure this OE oil from Amsoil results in good wear protection at normal OCIs. Contrasted to the other lubes from Amsoil, if I pay a little less money for a lot less OCI, that is a loss of content, and if you cannot see that, then you and I simply don't agree on how to measure the value of life's offerings. This OE oil prouduct in HDEO form offers 2/3 less OCI for only 1/3 less money. Is that not a loss of content?

And I admit I have no proof, but I VERY MUCH SUSPECT that Amsoil ALSO reduced the factors that put cost into the oil, such as lesser cost base stocks, additives, etc. It would be foolish of Amsoil to NOT reduce their cost factors in this product, would it not? So the reality is that we KNOW there is a loss of content in regard to OCI versus cost, and at least some of us suspect there is also a physical elemental input reduction as well.

This is a good market strategy for Amsoil. They make more money via higher sales frequency for a product that will very likely provide no more wear protection than a competing oil over normal operations in OEM OCIs, and quite possibly costs them less money to make due to the likely reduction of physical inputs.




Hmm,some valid points that are only answered by
A) being a hater

B) being a hater thats also a MOD

???????????????????????????????????????????????
 
Originally Posted By: jmimac351
When I picked it up I asked about the OE diesel oil and was told the additive package was different / not the same as the higher end stuff. It was suggested that there are some people who just do not buy into the longer drain intervals spec'd for their other oils and this OE oil, because of the price point, makes it more workable for that particular customer.

What I'll have to decide on is, is it better to spend $20/gal on this stuff or $10-$12/gal on Delvac, Rotella, etc. At almost twice the price, and shorter drain interval than the other synthetic, I'm not so sure. Rotella T6 is cheaper. I know very little about oil other than I prefer to have clean oil...



Ah - there you have it. Although I didn't contact them directly, I'll take jmimac351 at his word. Apparently Amsoil is indicating that the OE products (in HDEO) are decontended, for a lack of a more acceptable term.

So, let's review. I suspected that the OE product was "decontended"; seems I was right. I also pointed out the 2/3 reduction in OCI but only 1/3 reduction in price; is that escaping most everyone but me? I don't hate Amsoil; never have, never will. I have recommended Amsoil to several people (including my neighbor) when the situation warrants, for extended OCIs. They have excellent products that fit very well into some maintenance plans.

But as I've often said, they are not a one-size-fits-all answer for everything. Where most of the Amsoil lubes fit well into some extended OCI plans, this OE product really struggles to make much sense. It will, however, fill a niche previously unexplored by them; it will provide a lower cost alternative to those Amsoil junkies that want bragging rights, but don't want to pay (as much) for them. It's good marketing for Amsoil. However, as we most all would agree, the choice of lubricants for some people is much more based upon emotion than logic.

One last thought ...
My postion as a moderator is to enforce the rules and act in support to the ownership and administrators. That does not preclude my contributions via experience, education, and even opinons (which I have at least as many as the next guy). My participatation as a member is not limited by being a moderator, as long as I follow the rules I'm obligated to enforce. Feel free to point out all my violations to me or the staff or ownership. But could it be that my so called "Amsoil hatred" is just some common sense and logical analysis bubbling up through the rhetoric and hype? I've been very critical of RL and RP as well, but since they are not predominant in the HDEO forum as much as Amsoil, those brands simply do not come up as often. I've applauded many Amsoil users for extended OCIs, especially with bypass filtration. But I am NOT required to sit by and not say anything when interesting posts come up, and I have comments/questions. My status as a moderator does not entitle me to any special treatment, but it also does not restrict me from contributing either. This site is foremost dedicated to the open exchance of information for all things lubicant related; that's why we're here, and that includes me. So, in closing, if I've crossed a line and violated rules, then I would appolgize to all and offer myself for admonishment. If not, let's stick to the topic and leave diversionary tactics aside, please?
 
Last edited:
Status
Not open for further replies.
Back
Top Bottom