Recent content by naimc

And because of thread I am the new owner of a Kingbolden K8 , after coupons my price was around $383.65 USD. It was my door step a few days after ordering, its winter here so I have tired it yet. this android table is 100% in bedded in plastic, No access to batteries SD slots anything, not...

The different products from all these different brands are all locked in same silo's free update for lower end limited devices and anything more usefully will require a re-occurring subscription. I get they need a revenue stream. This thread and my neighbors quest to do actuation tests on...

Found the entire dumper breaks down to smaller sections and if I screw up I can get per-painted parts. But 1st I try to remove crumple with boiling water then I will try the heat gun from the inside and knowing my luck I will just burn off the paint and 100% ruin the part.

Hit an object on highway last week heard a bang just like rock to the windshield except the the windshield was fine. A few days later my wife asked if I hit a curb that's when I noticed 4 inch indentation on the bottom passenger side front bumper, and gap in front with a bulge on the side and...

Dam I separated my acromioclavicular (AC) joint just the day after I made this post so I have not been able to follow up. Fired up the thing today just letting free flow and stopped and started few times and no back fire. So it probably only happens when the engine is running on constant...

Yes there is a shut-off, but this is pressure washer with direct attached pump with a built in un-loader, that does not re-circulate the water. the the instant the pressure gun is shutdown the pump start over heating. They, ( the internet the owners manual all say that the engine should be...

This small 208 cc engine will back fire once when I turn off the ignition switch. It does it all the time. Other than that is runs fine. For winter storage I completely drain the gas and remove the pump and bring it inside Original when I purchased it 2 years ago I adjusted the valve lash...

I have not tried the pump yet, its been raining here for the past 3 weeks. Update, I tired this morning, With a small leak in my fittings the max psi I get is around 2500 psi. the unloader will bring give about 400 psi of downward adjustment. So yes it seems this is tuned for an electric...

I got my unit this afternoon, removed the cheap pump and leaking pretty bad. As I forwent the engineering verifications a vertical aliments said close enough ! Definity will need to replace the hex bolts but it fits ! Fantastic upgrade ! Thank you for posting your oil question and...

Princess auto sells this : Triplex Plunger Pump oil - 16 oz - ar64516 @ $14.99 (this is the stuff I put in my other AR triplex pump) https://www.princessauto.com/en/huile-pour-pompe-triplex/product/PA0008182123 This is under the AR blue brand , (AR consummer prodcuts), the oil is 30W-non...

Ok I was wondering why that was listed at $159 CAD that's under the cost of the generic clones. I ordered one yesterday gambled that its going to fit on my Costco , Husqvarna 3200 . The entry level AR pump on that unit leaked from day one and main shaft seal is impossible to replace. Even...

@dfarr67 , oil specs are here : https://arnorthamerica.com/pdfs/manuals/RC_RCS_RCA_RCV_Manual_2023.pdf page 16. I am looking at the same pump on Amazon to replace a RMV 2.5G30 Can't find an mounting diagram for the AR RCVU3G27D , wondering what the distance is between the mounting bolts ?

@Fordiesel69 , Yes I saw that video an others showing the importance of the leak down tests, I made gasket out of rubber for the exhaust port and found some silicon plugs. I did the leak down test with soapy water No leaks on pressure and vacuum test. Undid the carburetor again and watch a...

Update, I let the gasket soak as suggested , all the parts are super clean. Re-assembled and it's still leaking, not by much. I am waiting for new gaskets, while I wait I think I will try just a tiny line of gasket seal. I am now very familiar with this saw and can break it down and...

Put the fuel back in the saw, expecting nothing but success ! No go same issue, chains just run on bulb squirt , then bogs down on the trigger. there are few YouTube video's for this chainsaw and its always are carburetor issues. took the carb apart again, I did find some fuel under cab so...