N

NYEngineer

From LI, NY
Joined
Last seen
Viewing forum list
Messages
3,067
Reaction score
753

Latest activity Postings About

    • N
      NYEngineer reacted to D60's post in the thread New tool thread with Like Like.
      Oh and I should note gotta be reversible because LH bits are the best extractor. I stumbled upon a couple online that looked appealing...
    • N
      NYEngineer replied to the thread Using Impact Sockets only for 3/8” and 1/2” dr.
      Few years ago during a construction project at my job, there was a guy installing fire sprinklers. It was all No Hub or whatever you...
    • N
      NYEngineer replied to the thread New tool thread.
      That air drill is sweet.
    • N
      NYEngineer reacted to D60's post in the thread New tool thread with Like Like.
      After doing this on a 6.7 PSD EGR bolt with an M12 right angle drill, I knew I wanted 1) more compact and 2) more spindle speed for...
    • N
      NYEngineer replied to the thread Using Impact Sockets only for 3/8” and 1/2” dr.
      Forty years ago I worked in a marine engine machine shop. I was 19 years old so I was buying a lot of tools. Back then there were no...
    • N
      NYEngineer replied to the thread New tool thread.
      I have an 18 volt Milwaukee that I switch between an edger and a string trimmer. I like it a lot. Just sayin'.
    • N
      NYEngineer reacted to AutoMechanic's post in the thread New tool thread with Like Like.
      Tekton haul today. Old style 1-1/4 12 point socket not sure what the difference is in the new style versus these but decided to get it...
    • N
      NYEngineer replied to the thread New tool thread.
      In a pinch you can press a hex nut onto the square end of a tap and turn it with a socket. Works great in tight places.
    • N
      NYEngineer reacted to The Critic's post in the thread New tool thread with Like Like.
      For automotive it is a good idea to also have a full range of tap sockets. Those handles are generally too large to fit into tight areas.
    • N
      NYEngineer reacted to rondg's post in the thread New tool thread with Like Like.
      just sold my hf-start pulse TIG and got a new MIG. i don't TIG a lot so lift tig is fine (lift tig works great in this machine)
    • N
      NYEngineer replied to the thread New tool thread.
      My house had a click together floating floor in the basement bathroom. I've never liked it and knew I would have to pull it up and tile...
      • IMG_7911.webp
    • N
      NYEngineer reacted to Astro14's post in the thread Curt Hitch Holes misaligned. Fix? with Like Like.
      Bend it a hair more. Dremel out a bit of material in the one hole that’s still off, if needed. Use a thick washer on all 4 bolts to...
    • N
      NYEngineer reacted to Stimp's post in the thread 2023 Traverse 9 speed question with Like Like.
      I just flushed the 9spd in my parents 2019 Enclave at 50k mi. Pull the c-clip from the upper ATF cooler line at the top driver's side of...
    • N
      NYEngineer reacted to The_Jeff's post in the thread RC Cola pricing with Like Like.
      The cola companies pay big bucks for shelf space. It's even mentioned in We Didn't Start the Fire: "Rock and Roll, the cola wars, I...
    • N
      NYEngineer replied to the thread RC Cola pricing.
      I know it sounds strange. The restaurant is in Bayshore. I can't remember which one it was but I know it was Coke or Pepsi. They told...
    Show older items
  • Loading…
  • Loading…
Back
Top Bottom