Search results

The Accutire MS-4021B has always worked well for me and the price is right.

I recall cleaning it up after first use with soap and water but I don't bother cleaning it any more after use. I just pour out as much fluid as I can. I only use it for extracting oil from one car so there's no mixing different types of fluids.

Originally Posted By: RNMKia

Originally Posted By: RNMKia I cannot, for the life of me, get the oil filter off. I used a proper size band wrench and all it did was crush the filter without it budging, so i don't know what to do next (i tried putting large rubber bands around it for extra grip). I have no idea who would put...

Avoid using hand-tool sockets and adapters on impact wrenches that have a hog ring socket retainer. The hand-tool sockets/adapters have indents on the inner walls of the receptacle that the hog ring can get stuck in. This typically requires excessive force to remove the socket, which tends to...

To prevent leaks, use a new OEM washer each time and torque the drain plug to spec. Washers are cheap when purchased in quantity.

I've used suction pumps in the past but I'm planning on buying a Motive 1740 1.5 gallon Transfer Pump for filling differential and transmission fluid so I don't have to re-fill in between transfers. http://www.amazon.com/Motive-Products-17...e+power+bleeder I also have a Mityvac MVA6851 Fluid...

Originally Posted By: edyvw Originally Posted By: SIXSPEED I've used Mobil 1 Formula M 5W40, Mercedes Benz 5W40 and Castrol Edge 0W40 in my 2012 E350; all are good oils and meet the MB oil spec. Formula M is no longer available from my dealer but Mobil 1 0W40 is a good substitute. I have used...

I've used Mobil 1 Formula M 5W40, Mercedes Benz 5W40 and Castrol Edge 0W40 in my 2012 E350; all are good oils and meet the MB oil spec. Formula M is no longer available from my dealer but Mobil 1 0W40 is a good substitute. I have used oil filters from Mercedes Benz, Mahle and Purflux. The OEM...

It's probably a good idea to change the oil on a shorter OCI if you're idling the motor for extended periods to warm it up or making frequent short trips. This can potentially introduce more fuel and moisture into the oil reducing its effectiveness to lubricate and protect the motor.

I just finished up a brake pad replacement on our Odyssey that was rather noisy when the brakes were applied. I applied a thin layer of high temperature brake grease between the back of each brake shoe and the shim. I also applied a thin layer of grease on the ears of the shoes that fit in the...

I replaced the OEM Motorcraft battery in my 2007 GT500 in 2010 after three years because the seal on the negative post failed and corroded the terminal, but it still started the car just fine. I replaced it with another Motorcraft battery and it is still running strong after almost six years in...

I carry a smaller JNC300 in my daily driven vehicles, which have a V6 motor, but I also have a JNC660 for another car that has a V8 motor.

I have the 3/8" Milwaukee M12 and really like its utility working in tight confined spaces where it's difficult to swing a ratchet wrench. I chose the 3/8" for the extra torque. I don't ever recall wanting to adapt it down to 1/4". You can't go wrong with either one.

Originally Posted By: Ramblejam For around $25, you can have 20ft. 4-gauge jumper cables; these will last forever, work every time, and start anything on the road. Have you considered doing this? Yes but you still need a battery ... I'd rather be self reliant.

84 to 87 Buick Grand National (GNX)

From their website: Jack's plate – 3.5 -5 inches in diameter There are other critical dimensions for the floor jack to ensure compatibility; they are listed on the website. http://jackpoint.biz/

Got two of these Arcan Jacks at Costco to use with the Jackpoints.

I have the IR 20 gallon upright Garagemate. It's an excellent DIY compressor and has no problem running impact wrenches. But most of the time I use my cordless tools.

I really like my CTEK Muti-US 3300 charger.