Donaldson fuel filter cross reference?

Status
Not open for further replies.
Joined
Dec 27, 2003
Messages
754
Location
Oshkosh, WI
Our wrecker at work has a aftermarket fuel filter/water seperator paired with the extra capacity fuel tank, and the filter that's on it is a Donaldson P92 0711. I've tried to cross this into Wix or Hastings to no avail. I'd like to be able to run a Wix filter that could be obtained locally from Carquest or NAPA rather than having to order them from a diesel injection shop which is a half hour away and doesn't deliver to the shop. Even if there's a way to physically take the dimensions of this filter and get a Wix filter that's close and would fit just fine, that'd work too. I don't care if it's an inch or two longer or shorter, just so it's the proper threads and gasket diameter and will get the job done.

Thanks,
Mike
 
P920711


FF/WS 1GPM

Application Details


Fuel Filter Water Separators Product Attributes
A - OD (Inches): 4.38
B - ID (Inches): 1 1/4-12
C - Length (Inches): 7.44
Product Type Description: FUEL/WATER SEPARATOR SPIN-ON
Primary Application: 1 GPM HIGH PERF FF/WS
Substitution: P920683=3 GPM (longer version)

P920683


FUEL FILTER ASSY. 3GPM

Fuel Filter Water Separators Product Attributes
A - OD (Inches): 4.38
B - ID (Inches): 1 1/4-12
C - Length (Inches): 11.75
Product Type Description: FUEL/WATER SEPARATOR SPIN-ON
Primary Application: 3 GPM HIGH PERF FF/WS
Substitution: P920711=1 GPM (shorter
Substitution 2: version)

Filtermart has a replacement ..$$

But..... There are a few that share the same thread.. This is allegedly for a Cummins in a Wix x ref from Donaldson's site.

Part Number: 33116
UPC Number: 765809331167
All Applications
Style: Spin-On Fuel
Service: Fuel
Media: Paper
Height: 11.345
Outer Diameter Top: 4.668
Outer Diameter Bottom: Closed
Thread Size: 1 1/4-12
Drain: None

Gasket Diameters
Number O.D. I.D. Thk.
Attached 4.320 3.820 0.365

The Donaldson

P550687

Fuel Filter Water Separators Product Attributes
A - OD (Inches): 4.74
B - ID (Inches): 1 1/4-12
C - Length (Inches): 11.8
D (Inches): 4.39
E (Inches): 3.87
Product Type Description: FUEL/WATER SEPARATOR SPIN-ON
Primary Application: CUMMINS 3309437
Substitution: P550202=Standard Fuel

Donaldson doesn't appear to give the gasket specs. If you can spin off your filter and measure ..you can see what works.

After a little more extensive search of the Don-site. There are only 3 filters using the 1 1/4-12 thread that are FF/WS.

Good luck and kindly share your success with the others on the board.
smile.gif


[ November 25, 2004, 07:24 PM: Message edited by: Gary Allan ]
 
I think you might be out of luck trying to cross that SPECIFIC number.
I did a search (I kind of like a challenge) and came up with a link to this PDF manual-(864k)

http://www.mantiscranes.com/Customer_Support/Manuals/8010_Operators_Manual.pdf

It lists that Donaldson PN in the replacement filter section on page 49.
For some filters, it lists other brands. Not for that one however.

Looks like it's time for plan "B".
 
Here's a Baldwin in the same thread:

PART NUMBER: BF1216

Descriptions : Microlite Fuel/Water Separator Spin-on with Drain
Contains : Integral Post Seal
Fits : Cummins Engines
Replaces : Cummins 3309437
Thread : 1 1/4-12
O.D. : 4 11/16 (119.1)
Length : 12 3/32 (307.2)
I.Gskt : [1] Included
Related to : BF596 (Fuel Version)
 -


You should be able to tell by the image if the gasket is anywhere near yours.
This works at filtermart for about $39

Here are the Wix version of the BF596 (fuel only)
Gasket Diameters
Number O.D. I.D. Thk.
Attached 4.320 3.820 0.365

It does look like you're stuck if you require a FF/WS filter.
 
Status
Not open for further replies.
Back
Top