Search results

  1. T

    Craftsman 4-ton Jack Problem

    Thanks for all the input. I have replaced the fluid. I will open and inspect the metal end seat closely for possible options. It is recessed ~ 2-inch so a punch might create a new surface. Not much downside to trying. I checked HF today for jack options. regards
  2. T

    Craftsman 4-ton Jack Problem

    I have a Craftsman 4-ton jack (50156) that slowly leaks down. Sears does not show any parts available for this model. I have replaced the oring on the lock valve shaft several times. The oring appears to fit snugly to the valve shaft and bore. However the lock valve appears to seal by...
  3. T

    '04 Honda Accord V6 Fuel Injection question

    Is miss random or put-put-put (same cylinder). Random miss is unlikely to be an injector miss. Injector cleaner is in autogas now and problems are rare. More likely to be valves or EGR system (V6 and I4 are notorious for problems). If it misses cold, suspect a leaking EGR valve. PCV should be...
  4. T

    Cheap Hong Kong Obd2 Scanners

    Has anyone else tried to use the many variations of Obd2 scanners available for use w/ laptops from ebay. Following is a typical example and identical to one I tried. Costs are low; Ebay Obd2 Scanner I installed (no detailed instructions) the scanner software (elmscan download) and the USB...
  5. T

    Looking for a manly Torque Wrench!

    I have "calibrated" my 1/2" cheap torque wrench as follows: 1) Measure position on the handle: 14" as center of force application. 2) Stand on good quality bathroom scale and apply force to wrench restrained in vise. Force must be straight up/down to subtract/add to observed weight. I...
  6. T

    2001 Accord VTEC engine problems low oil

    On OBD1 Hondas there were only two Vtec DTCs; one for electrical failure in the vtec solenoid, and other for electrical fault in the Vtec pressure switch. Both of these codes are electrical faults, that is ECU detected short or open in the circuit. I could not find any references to DTC 1259 in...
  7. T

    92 Accord: Engine stutters upon acce

    There is a procedure for cleaning the EGR ports and passages. EGR valve rarely seems to be the problem and is difficult to clean (pintle obstructs access to sealing surface). PM your email address and I'll forward a pdf of the cleanout procedure. I think your model has the improved EGR manifold...
  8. T

    92 Accord: Engine stutters upon acce

    Missing on a warm engine can be caused by coolant leaking onto plugs causing short. I had this on 94 Accord. If you're not losing coolant then problem is likely electrical; coil, wires, distributor cap, or rotor. EGR won't cause missing in my experience, only hesitation. As pointed out...
  9. T

    Ramps Sliding

    I use short (18") pieces of 2x6 to bridge from ground to about 3" elevation on the ramp. This allows a car w/ low ground clearance to mount the ramp w/o bumper hitting ramp. Of course, you use same pieces to come down the ramps. This procedure works good for an automatic, but w/ a manual trans...
  10. T

    Fuel Grades vs. MPG

    There's another source of bias that you would be desirable eliminate. When you know you are using 87 or 91 grade, you may subtly alter your driving technique. This is not conscious, but is unavoidable if you know what fuel is in the tank. To avoid most bias, you will need to drive the car w/o...
  11. T

    Honda low on oil, again.

    I have a 2007 Accord SE 4-cylinder, similar miles, and I haven't had your problem, however I recently changed may oil and noticed something that may be related. The oil change spec is 4.4 US qts w/ filter change. When I changed oil w/ that replacement amount, I was down to the add oil mark on...
  12. T

    2001 GM 3.4L V6 Cyl 1 Missfire

    If you're losing any coolant, you may have a head gasket leak. I had same symptoms on 94 Accord EX; missing badly for 0-2 minutes after a warm startup. I figured out which cylinder was missing, and pulled plug after stopping warm engine (water on plug). good luck
  13. T

    Interdynamics R134 Manifold Gauge Valve Repair

    My Interdynamics R134a Manifold Gauge set is about 20 yrs old. It has served me well over the years w/ only a few uses per year. I recently used it and noticed the high side hose end shut-off valve was completely blocked (whether open or closed valve position). After disassembling the top-entry...
  14. T

    Strange odor coming from my car??

    The lubricant used in some AC systems Polyalkalene Glycol(PAG) smells something like hairspray, a sweet, aromatic odor, not unpleasant. It is persistent. This could mean an evaporator leak. good luck
  15. T

    Changing head gasket on 2.2 Pontiac..any tips?

    Get a manual of some type and make sure you understand how to insure the crankshaft and camshaft timing relationship is maintained when you remove timing belt or timing chain from the camshaft sprocket. good luck
  16. T

    Handheld Scanners

    I have used Harrison R&D OBDScan software, hardware, and a laptop for 5-6 years and am very satisfied. Perhaps not quite as handy as a handheld dedicated device, but it works very well and price is similar; $140. I spent ~$100 on a older used IBM laptop. Harrison is very good w/...
  17. T

    Got some front end work done, still some issues.

    Toe is usually adjusted to obtain correct toe-in, but they ignore position of steering wheel (off center). This requires a little extra effort to both center the steering wheel and align toe-in. I too have been severely disappointed w/ alignments that usually result in same performance as...
  18. T

    pcv systems

    Originally Posted By: rg200amp This is gonna sound STUPID, but. . . . I have been wondering for a while, and no one can give me a good answer. My 04 LS has the 3.9L AJ-V8. Whenever I look to see if I can replace the PCV I allways get "you do not have one" Both Lincoln and Jaguar dealers told me...
  19. T

    pcv systems

    If air from intake were routed to the crankcase, then under high load conditions the reverse PCV flow would pickup oil-laden crankcase vapor and pull it into the intake duct. You would lose a lot of oil. As it is there is still some oil in the vapors in the valve cover and the oil causes grime...
  20. T

    RhinoRamps Storage & Minimum Temperature

    I looked at the Rhino Ramp web site and was unable to find any specifications. They mention a "foam core" design. This implies a sandwich of plastic outer skins surrounded by foam. Brittle behavior would be dangerous as this design depends on the skin of plastic remaining secure and bonded to...
Back
Top