Search results

I am looking to hear from someone who has handled the below problem with a New York State boat trailer registration. I am aware what the NYSDMV has on their site. I have purchased a used boat trailer here in New York last registered in 2012. I have the expired 2012 registration tag on the NYS...

I posted in different forums here about repairs to my recent purchase. 2008 Ford Ranger. This fall it will get new tires. Until then, I want to remove one wheel at a time and clean up, repair, refinish these wheels. I have watched the acid videos and others. I am asking the advice of those...

This ATV has near 2000 miles on it. Good running. I have purchased a new rotor, pads and replacement bolts. As shown in the photos, the hex mounting bolts have been rounded off and are solidly corroded in place. Is the only answer to remove the rounded off bolts is grinding the heads off and...

Can the clutch plate, shims and pulley hub be serviced as located without un-mounting the compressor? Most video viewed shows the removal and replacement in a bench setting. I want to complete the tasks by taking the serpentine belt off and going after it without having to evacuate the...

I am looking at a pristine truck as listed above. It has the installed towing package. 4WD. 72000 miles. It was not used for towing however if purchased will used for towing a small boat and ATVs on an appropriate trailer. The listed specs I have seen when searching indicates a 6000 lb. towing...

I have an old Sony Vaio VGN AR630 that has been in storage for quite sometime. I used it overseas as a personal laptop to watch movies. It has the original 320 GB hard drive taking a maximum 4 GB RAM with Windows Vista Home Premium 32 bit installed. It seems to have use if I installed a new...

For at least two weeks I've had sporadic ABS/TC indicator lights come on. This vehicle has had three of the four wheel bearings replaced. Last week I noticed a puddle of brake fluid at the driver's rear wheel. This is the wheel that has not had the wheel bearing replaced nor makes noise. Good...

Odd circumstances. Vehicle ( 55463 mi. ) ran over 200 miles to my garage. It is my MILs vehicle and I maintain it. It was prepped for winter with wiper blades and fluid inspections when I noticed a driver's rear reverse light out and moved to replace it. I noticed it was just loose in the socket...

These four of the same aluminum items were found in an unmarked box with working tools like a Stanley No. 59 doweling jig. Can any one identify them for me? Thanks.

The starter is for an Ariens Snowblower. The internal black brush housing assembly which is wired to the external push button switch has one of its four brush housings partially torn off making the entire starter unusable. Parts on ebay listed as Tecumseh starter brush housings have a metal...

2009 Honda CR-V - 54000 miles Air conditioning gauges are showing 72 psi on both the low side and high side with no change when vehicle is started and air conditioning put on. A 1000 rpm is noticed when the A/C is turned on. The A/C 4 pin relay in the main fuse panel is tested good by swapping...

Last posts about this 2007 Buick Lacrosse with 52K was replacing the driver's front wheel ABS bearing (AC Delco $100) and the rear right wheel ABS bearing (SKF $77). Not much more than a week into a nice quiet smooth running vehicle, I begin to hear a groaning sound from the front again. This...

Getting constant rear wheel bearing groan on the below listed 2007 Buick Lacrosse. Sounds like right rear and will take the time to check out in the garage shortly. Vehicle has 50k on it with new struts on all four put on last year. Will replace both sides. Am reaching out for recommendations...

Received my order of 4 Engine/Transmisssion Mounts from RockAuto today and upon inspection of all, the transmission mount that sits on top but under the battery for the 2006 Pontiac G6 2.4 looked like this. The other three looked OK but this looks like a crack in the rubber through the other...

http://s219.photobucket.com/user/yazhere/slideshow/Pure-One%20Tear Code Indicates this last filter was manufactured December 2012. Used October 2015 until June 3, 2016 - approx 6000 miles. (3387a)

K&N filter used for 7500 with Shell Full Synthetic on 2010 Mazda 3i. Lots of oil left in the can after tear down. No issues. Fram PH3614 used for 50 hrs. on a B&S Vanguard 16 HP mounted in a 1994 Troybilt Garden Tractor. Rotella 15W40 used in the tractor @ 25hr.intervals...

https://www.flickr.com/photos/yaz4reel/22650684525/in/dateposted-public/ Looks good to me.

https://www.flickr.com/photos/yaz4reel/22534797212/in/photostream/ At least a couple of years back, a BITOG member posted a sale of Fram HM filters at Summit Racing under clearance pricing. I maintain at least ten family and elderly neighbor friends vehicles and use BITOGs forums to purchase...

This vehicle was purchased new in the family and never used much or abused. It has not seen pothole city driving or aggressive roadway driving. It has strut assemblies on all four. There are no suspension noises or visible signs of leaks in the struts. There are no noticeable signs of excessive...

I'm looking at a set of 4 to put on the 2007 Buick Lacrosse OEM chrome 17 wheel/rims. I have a set of separate winter wheels so whatever is purchased will run in three seasons. Price is about $40 a set more for the Cooper CS5s. Cooper CS5 Grand Touring or BF Goodrich Advantage T/As Any...