Recent content by J_Myler

  1. J

    Tachometer problems 99 Acura Cl

    Originally Posted By: Tegger Originally Posted By: J_Myler The tach will jump around from 0rpms to around 3000 rpms. Is this the original factory tachometer? Is the Check Engine light on? Are any other gauges not working? Yes it's an OEM tach, there isn't a CEL on and all the other gauges...
  2. J

    Tachometer problems 99 Acura Cl

    Originally Posted By: JHZR2 Ram Rod tach? Is there no OEM one? Wouldnt the odometer be in the OE cluster versus this? This behavior is classic of the amplifier for a hall effect RPM sensor that we see all the time on MB diesels. What is the nature of the pickup and electronics driving the...
  3. J

    Tachometer problems 99 Acura Cl

    Here is an update. The tach will jump around from 0rpms to around 3000 rpms. I'd hate to lose my odo reading of 223.550 miles. its a thing of pride for myself.
  4. J

    Tachometer problems 99 Acura Cl

    Hello all! My trusty steed Car Ram Rod tachometer has stopped working which really sucks. Here's a little bit of detail on the car is a 1999 Acura CL 2.3 with a 5speed trans and has 223xxx miles on him and runs like scalded cat. I can't think of anything else you might need to know. I did some...
  5. J

    Clutch problems

    The master cylinder is seeping just a tiny bit of fluid. Just enough to see with a bright flashlight.
  6. J

    Clutch problems

    Okay I just bled it out and its doing the same thing, The clutch isn't disengaging. Maybe the clutch master cylinder needs replacing?
  7. J

    Clutch problems

    I'm not losing any fluid I thought of bleeding it and adjusting the clutch peddle to see if that helps but I didn't want to make it worse.
  8. J

    Clutch problems

    I'll start with the car and describe the problem. Its a 99 Acura cl 2.3 with a 5 speed trans it has 210,xxx miles on it. And I can't get it into any gear when its running. If it's not running there isn't a problem getting it into any gear. More details, it had its clutch replaced about 8,000...
  9. J

    Outer tir rod end removal help!

    I can't even get the jam nut lose. Are the Threads revirse? On this car? Even such a thing?
  10. J

    Outer tir rod end removal help!

    I got the end off of the knuckle I'm trying to get the end off steering rack. Da' gun Michigan rust. Yes, I have new tir rod end for both sides. These [censored] are lose as heck.
  11. J

    Outer tir rod end removal help!

    Okay so, I'm trying to remove my outer tir rod end. I've soaked them in pb blaster and no luck. I would try a torch to heat it up but I don't have one and I'm at my parents in cookeville TN and don't know too many people here. But I need help asap because I'm heading back to flint tonight and I...
  12. J

    help please!

    car, 99 acura cl 2.3. I've been trying to get off the driver side wheel hub nut off. So far I've broken 5 half inch rechets and my only half inch breaker bar and I'm using a 3 foot chetter bar with my 200lbs frame to try and break it lose and nothing. I have no air tools that I can use. Any help...
  13. J

    F23A1 Rear main seal replacment

    Hello everybody! This weekend I'll be reaplacing the clutch and flywheel as well the rearmain seal because the flywheel will be off and I'm in there any way. I'm using a OEM exedy clutch and flywheel and a Amsoil mtf. I've never done anything this indepth with cars before, but I'm good with cars...
  14. J

    Time to replace the clutch.

    Okay, so here's the deal. I have a 99 Acura CL 2.3 with a 5speed trans and has 192,xxx miles on it and I need to replace the clutch and flywheel in the coming months and I want a high quality clutch and flywheel. Maybe OEM? But I don't know much past that so if anybody could help me out and...
  15. J

    Cars I hate

    Originally Posted By: GROUCHO MARX I hate those cars with the flashing lights on top, driven by guys in uniforms, that pull me over to inform me of a traffic law that I may not have observed. Haha Me too!
Back
Top