Search results

This is the front axle of an 2013 AWD Express. He's had a persistent leak at the RH axle seal. Note this is at the end of a bolt-on "extension tube", just inboard of the CV companion flange. He had a (terrible) local shop replace the seal due to initial leak. It was still leaking ~6 months...

Has anyone here re-sealed a timing cover on the 2.0T in the KL Cherokee platform? I'm looking at one.....95% sure it's timing cover after using dye. It's leaking behind the motor mount so visibility is near zero at the actual source Info on this engine in the KL is nearly non-existent -- I...

I'm trying to replace the boot on the front inner joint of a '15 Forester, 2.5NA Per VIN from dealer I have the OEM boot kit 28397SG000 However the inner boot has three lobes molded into it which prevent anything resembling a good fit. Please see new boot on right: Poor fit (worse in person)...

I'm likely going to need to troubleshoot the inverter cooling system on a '13 Hybrid. It's dripping at left front of vehicle, but with lower splash shield in place everything is a guess right now. Reservoir for the inverter system is empty. I think he drove maybe 6 miles after a P0A93. How...

Here's a dumb question, which in this case would apply to an AB60F in a Tundra: If a guy (mild PITA customer) drives his Tundra over thus it's at operating temp, about how long for the trans fluid to drop under 100*F so fluid level can be accurately checked after a spill 'n fill? I'm pretty...

I just installed these Sunsong hoses on the rear of a '12 Ram 1500 4wd They come with replacement hardline because the factory doesn't provide a threaded fitting at the hose/hardline junction. I bled with wheels removed on my lift and then lowered it to slap the wheels on. I never thought to...

First, I'm an idiot. Let's get that out of the way. Now, I was just trying to verify fluid level in the rear diff of an '08 Range Rover Sport. I thought the fill plug was on the front, but it's a pin of some sort. Here's a vid of a guy who made the same mistake: You don't need to watch...

Working on an '02 Forester normally aspirated. Regarding the evap purge valve in the engine bay on passenger side of engine kinda tucked under the intake manifold: should you not be able to blow through it in either direction? I cannot blow through from firewall to intake, which I believe...

The WIN in this '12 Ram 1500 requires the typical push 'n wiggle (not legal in all 50 states) to start the truck I need to address it but am unclear if it must be serviced, or can simply be replaced -- and if the latter if it will need to be programmed There are services like this that claim...

Searched but couldn't find any similar threads except for 2007 from @Pablo about Amsoil. When it comes to commercial accounts, does anyone have preferences between O'Reilly, AutoZone, NAPA (or others like AAP)? Better promotions or pricing? Better resources on their pro site? Something else...

I'd like to get a proper bottom fill setup with a decent selection of adapters. If it matters, I don't necessarily need euro -- figure mostly domestic and Toyota/Nissan The thing is, I'm all over the map: do I just want adapters (and cobble on my manual pump), or do I want a basic reservoir...

In today's episode of Things that Make You Go Hmmmm Automotive edition: I've always wondered why caliper slider pins are typically sold as two (enough to service one caliper), but slider pin boots are sold as a pack of four (enough to service two calipers). I've gotta watch myself with online...

I have this VIM roto head ratchet. Granted, it's kind of an oddball but not that old -- ordered new from Amazon November '22 The ratchet mechanism has locked up. It's basically completely seized. Somewhere in there something else went awry because pushing the QR button does not release the...

Check your local TSC for clearance on these items and more. Should be repeatable for all as IME TSC clearance prices are nationwide ‐- post up results. I do also believe clearance prices show online. 12oz bottles of Techron are $3.99 (looks to be around $13 on Amazon right now) Gallons of...

I'd like to order an a/c compressor for a '00 Cavalier with 2.2. Vehicle is presently not in my possession and --of course-- parts listings ask if a 5/8" or 3/4" suction port. And again of course, not all listings specify or even mention port size. Thus, I'd be inclined to order one of those...

I apologize if this has been posted. I searched and didn't see it. This is presumably a factory in India. I see so many problems here: - Not sure how they maintain concentricity with 3-jaw chucks. -They seem to just flip the rotor to face it, not sure how they keep both sides parallel. (I've...

I need to order an aftermarket TAD (traction aiding diff) for a '13 Express 1500 AWD. Research indicates this should be your standard 10b/8.6 and 30 spline. Customer wants an Auburn Select-A-Loc. What gives me pause is at retailers like Summit Racing it claims part 545004 will fit a 2012, but...

I had a client just purchase an '08 Land Rover Range Rover Sport. Supercharged. Mileage unk. No, he didn't consult me. I'm the only wrench he trusts so I know I'll be asked to fix pretty much anything that goes wrong. What are common issues/failures? Gotchas? Repairs I should absolutely...

Looking at a '19 Cherokee with the 2.0T and a whopping 25k miles. Complaint is a (surprisingly healthy) oil leak. It very much appears to be coming from the RH cam/VVT actuator in the front of the valve cover. I checked all three retaining bolts and they're tight (loose fasteners anywhere and...

I'm not thrilled with my "paint can" Autoline smoke tester. Just doesn't seem to produce much smoke. I'm using the actual Redline fluid, but not sure if that's necessary? ANYWAY I'd like to step up to a nicer machine with flow meter. Please, if you DIY'd one that's great but I don't have the...