Search results

I am also slightly tempted to reuse the original hub although it has 150k on it. 06 Toyota Sequoia. But hoping the new Quality Built has some quality to it. It can’t be too difficult to make a good hub, right?

Correct bearing from Rock Auto. It’s a Quality Built kit that came with the hub. Never again. I spun it last night and it makes noise so gonna press the hub and bearing back out. Ordered an SKF bearing after doing some research on bearing quality. A tone ring and a spacer will caver the...

I attempted my first wheel bearing job and was hoping for some advice. I supported the inner race of the bearing when pressing in the hub but still noticed it somehow pushed out a little on the one side after the hub fully seated. (Picture below but hard to see). It sticks up about 1/8” on...

Update: I took the car to work this morning and within 300 feet after pulling out of my driveway the ABS light went out! I am guessing that cleaning the reluctor ring and removing the corrosion where the wss fastens resolved the issue. The ring was dark colored with road dirt and brake dust...

I ordered one off Amazon to be delivered Tuesday compatible for an iPhone. Will report back. Thanks to everyone for the assistance.

Sorry about that. Rookie at using multimeter. I get 26.47 ohms on the sensor at rest but when I spin the wheel the ohms reading does not change. I wire brushed the area where the sensor bolts on to in case there was something keeping the sensor from being close enough to the reluctor ring but...

Got the chance today to diagnose. I unplugged the sensor at the wheel and checked teeth on the reluctor ring. They are all there and was not corroded but used some brake cleaner, rag and screwdriver to clean up anyway. Shines like new! Hooked back up to the wheel and then unplugged the other...

Thanks Astro. I will ask around to see if anyone I know locally has the Ford forscan software. I’d be delighted to reimburse them for their time, effort and expenses as I would be grateful. Just didn’t want to overpay a dealer but might have to go that direction. I got the wss from Rockauto...

Innova 6030P is the scanner and the wss is a Standard Motor Products ALS2371. I see where you may be going with this. Does the wheel speed sensor speak a different language than the ABS system? Gonna have to get a different wss?

ABS light and Service Advancetrac message came on a few weeks ago on my 2010 Fusion. Noticed at slow speeds coming to a stop the brake pedal pulsing. Hooked up my scanner and pointed to driver side rear wheel speed sensor which I promptly replaced. Pedal issue went away but ABS light stays on...

Yes, I was thinking it should go here somewhere on the middle seat belt but does not fit on there.

I replaced the cables/regulator for the electric sliding rear window on my 2011 Sierra Crew Cab. It required me to remove the back seats and the plastic trim below the window. Ended up having a small piece shaped like a suitcase handle or squared off C with #15913744 and >PDM< #10363 and PWR on...

Upon locating the Canister Purge Valve unit on the inner passenger side fender well behind the engine and along the firewall I attempted to remove it tonight after work. I had to take the air intake manifold off and squeeze my hand back there to try and unhook the two hard plastic lines that...

New coils and ijectors did not correct the problem as predicted. For kicks I took it to Autozone to hook up to their diagnostic reader. It threw the lean condition in both banks and points to replacing the canister purge solenoid. I did some research on these and they can actually cause a lean...

Ordered a set of fuel injectors since I will have everything apart and will replace them the same time I replace coils and spark plugs. Good maintenance as she is planning to keep the car a few more years. It has been a problem free vehicle to this point so not complaining at all about it. If...

Replaced lower intake manifold gaskets and also the new throttle body did not fix it. Took to local garage and his code reader suggested cylinder #3 misfire. He cleared code and swapped coils and plugs with cylinder #6. Started car and threw code pointing to cylinder #3 misfire which ruled out...

Sorry, no pictures. But it was about the size of a cantaloupe. As a last ditch effort before taking to a garage I ordered a new throttle body and will report results.

Did try the idle relearn a few times early on in this process but the car would usually stall a few times before coming up to temperature and completing the full process. And I remember turning the AC on per the relearn instructions and noticed that the rough idle went away while the AC was on...

Fuel Injector Resistance: Cylinder #1 12.5 ohms, Cylinder #2 12.5 ohms, Cylinder #3 12.7 ohms, Cylinder #4 12.5 ohms, Cylinder #5 12.5 ohms, Cylinder #6 11.1 ohms. Acceptable range is 11-18 ohms so although #6 is lower I don't think that is the problem. Ignition Coil Resistance: Cylinder #1 B+...

Thank you for the advice on the fuel trim numbers. I don't have the equipment to do that. Tried a new Manifold Intake Pressure switch and did not resolve the issue. Ruled out EGR valve as it is working properly. Replaced upper intake manifold gaskets while I had it apart as a known problem...